Ohm's Law

There are certain formulas in Physics that are so powerful and so pervasive that they reach the state of popular knowledge. A student of Physics has written such formulas down so many times that they have memorized it without trying to. Certainly to the professionals in the field, such formulas are so central that they become engraved in their minds. In the field of Modern Physics, there is E = m • c². In the field of Newtonian Mechanics, there is F_net = m • a. In the field of Wave Mechanics, there is v = f • λ. And in the field of current electricity, there is ΔV = I • R.

The predominant equation which pervades the study of electric circuits is the equation

ΔV = I • R

In words, the electric potential difference between two points on a circuit (ΔV) is equivalent to the product of the current between those two points (I) and the total resistance of all electrical devices present between those two points (R). Through the rest of this unit of The Physics Classroom, this equation will become the most common equation which we see. Often referred to as the Ohm's lawequation, this equation is a powerful predictor of the relationship between potential difference, current and resistance.

Ohm's Law as a Predictor of Current

The Ohm's law equation can be rearranged and expressed as

As an equation, this serves as an algebraic recipe for calculating the current if the electric potential difference and the resistance are known. Yet while this equation serves as a powerful recipe for problem solving, it is much more than that. This equation indicates the two variables that would affect the amount of current in a circuit. The current in a circuit is directly proportional to the electric potential difference impressed across its ends and inversely proportional to the total resistance offered by the external circuit. The greater the battery voltage (i.e., electric potential difference), the greater the current. And the greater the resistance, the less the current. Charge flows at the greatest rates when the battery voltage is increased and the resistance is decreased. In fact, a twofold increase in the battery voltage would lead to a twofold increase in the current (if all other factors are kept equal). And an increase in the resistance of the load by a factor of two would cause the current to decrease by a factor of two to one-half its original value.

The table below illustrates this relationship both qualitatively and quantitatively for several circuits with varying battery voltages and resistances.

	Circuit Diagram	Battery Voltage (ΔV)	Total Resistance ()	Current (Amps)
1.		1.5 V	3	0.50 Amp
2.		3.0 V	3 Ω	1 Amp
3.		4.5 V	3	1.5 Amp
4.		1.5 V	6	0.25 Amp
5.		3.0 V	6	0.5 Amp
6.		4.5 V	6 Ω	0.75 Amp
7.		4.5 V	9 Ω	0.50 Amp

Rows 1, 2 and 3 illustrate that the doubling and the tripling of the battery voltage leads to a doubling and a tripling of the current in the circuit. Comparing rows 1 and 4 or rows 2 and 5 illustrates that the doubling of the total resistance serves to halve the current in the circuit.

Because the current in a circuit is affected by the resistance, resistors are often used in the circuits of electrical appliances to affect the amount of current that is present in its various components. By increasing or decreasing the amount of resistance in a particular branch of the circuit, a manufacturer can increase or decrease the amount of current in that branch. Kitchen appliances such as electric mixers and light dimmer switches operate by altering the current at the load by increasing or decreasing the resistance of the circuit. Pushing the various buttons on an electric mixer can change the mode from mixing to beating by reducing the resistance and allowing more current to be present in the mixer. Similarly, turning a dial on a dimmer switch can increase the resistance of its built-in resistor and thus reduce the current.

The diagram below depicts a couple of circuits containing a voltage source (battery pack), a resistor (light bulb) and an ammeter (for measuring current). In which circuit does the light bulb have the greatest resistance? Click the See Answer button to see if you are correct.

See Answer

The Ohm's law equation is often explored in physics labs using a resistor, a battery pack, an ammeter, and a voltmeter. An ammeter is a device used to measure the current at a given location. A voltmeter is a device equipped with probes that can be touched to two locations on a circuit to determine the electric potential difference across those locations. By altering the number of cells in the battery pack, the electric potential difference across the external circuit can be varied. The voltmeter can be used to determine this potential difference and the ammeter can be used to determine the current associated with this ΔV. A battery can be added to the battery pack and the process can be repeated several times to yield a set of I-ΔV data. A plot of I versus ΔV will yield a line with a slope that is equivalent to the reciprocal of the resistance of the resistor. This can be compared to the manufacturers stated value to determine the accuracy of the lab data and the validity of the Ohm's law equation.

Quantities, Symbols, Equations and Units!

The tendency to give attention to units is an essential trait of any good physics student. Many of the difficulties associated with solving problems may be traced back to the failure to give attention to units. As more and more electrical quantities and their respective metric units are introduced in this unit of The Physics Classroom tutorial, it will become increasingly important to organize the information in your head. The table below lists several of the quantities that have been introduced thus far. The symbol, the equation and the associated metric units are also listed for each quantity. It would be wise to refer to this list often or even to make your own copy and add to it as the unit progresses. Some students find it useful to make a fifth column in which the definition of each quantity is stated.

Quantity	Symbol	Equation(s)	Standard Metric Unit	Other Units
Potential Difference (a.k.a. voltage)	ΔV	ΔV = ΔPE / Q ΔV = I • R	Volt (V)	J / C
Current	I	I = Q / t I = ΔV / R	Amperes (A)	Amp or C / s or V / Ω
Power	P	P = ΔPE / t (more to come)	Watt (W)	J / s
Resistance	R	R = ρ • L / A R = ΔV / I	Ohm (Ω)	V / A
Energy	E or ΔPE	ΔPE = ΔV • Q ΔPE = P • t	Joule (J)	V • C or W • s

(Note the unit symbol C represents the unit Coulombs.)

Check Your Understanding

1. Which of the following will cause the current through an electrical circuit to decrease? Choose all that apply.

a. decrease the voltage

b. decrease the resistance

c. increase the voltage

d. increase the resistance

See Answer

Answers: A and D

The current in a circuit is directly proportional to the electric potential difference impressed across the circuit and inversely proportional to the resistance of the circuit. Reducing the current can be done by reducing the voltage (choice A) or by increasing the resistance (choice D).

2. A certain electrical circuit contains a battery with three cells, wires and a light bulb. Which of the following would cause the bulb to shine less brightly? Choose all that apply.

a. increase the voltage of the battery (add another cell)

b. decrease the voltage of the battery (remove a cell)

c. decrease the resistance of the circuit

d. increase the resistance of the circuit

See Answer

Answers: B and D

The bulb will shine less brightly if the current in it is reduced. Reducing the current can be done by reducing the electric potential difference impressed across the bulb (choice B) or by increasing the resistance of the bulb (choice D).

3. You have likely been warned to avoid contact with electrical appliances or even electrical outlets when your hands are wet. Such contact is more dangerous when your hands are wet (vs. dry) because wet hands cause ____.

a. the voltage of the circuit to be higher

b. the voltage of the circuit to be lower

c. your resistance to be higher

d. your resistance to be lower

e. the current through you to be lower  

See Answer

Answer: D

Wet hands have less resistance and thus less hindrance to the flow of charge; the current would thus be increased. Touching an outlet with wet hands increases the risk of charge flowing through you and causing electrical shock or even electrocution.

4. If the resistance of a circuit were tripled, then the current through the circuit would be ____.

a. one-third as much

b. three times as much

c. unchanged

d. ... nonsense! There would be no way to make such a prediction.

See Answer

Answer: A

Current is inversely proportional to the resistance. A threefold increase in the resistance would cause a threefold decrease in the current.

5. If the voltage across a circuit is quadrupled, then the current through the circuit would be ____.

a. one-fourth as much

b. four times as much

c. unchanged

d. ... nonsense! There would be no way to make such a prediction.

See Answer

Answer: B

Current is directly proportional to the voltage. A fourfold increase in the voltage would cause a fourfold increase in the current.

6. A circuit is wired with a power supply, a resistor and an ammeter (for measuring current). The ammeter reads a current of 24 mA (milliAmps). Determine the new current if the voltage of the power supply was ...

a. ... increased by a factor of 2 and the resistance was held constant.

b. ... increased by a factor of 3 and the resistance was held constant.

c. ... decreased by a factor of 2 and the resistance was held constant.

d. ... held constant and the resistance was increased by a factor of 2.

e. ... held constant and the resistance was increased by a factor of 4.

f. ... held constant and the resistance was decreased by a factor of 2.

g. ... increased by a factor of 2 and the resistance was increased by a factor of 2.

h. ... increased by a factor of 3 and the resistance was decreased by a factor of 2.

i. ... decreased by a factor of 2 and the resistance was increased by a factor of 2.

See Answer

A circuit is wired with a power supply, a resistor and an ammeter (for measuring current). The ammeter reads a current of 24 mA (milliAmps). Determine the new current if the voltage of the power supply was ...

a. I_new = 48 mA (Current is directly proportional to voltage; a doubling of the voltage will double the current.)

b. I_new = 72 mA (Current is directly proportional to voltage; a tripling of the voltage will triple the current.)

c. I_new = 12 mA (Current is directly proportional to voltage; a halving of the voltage will halve the current.)

d. I_new = 12 mA (Current is inversely proportional to resistance; a doubling of the resistance will halve the current.)

e. I_new = 6 mA (Current is inversely proportional to resistance; a quadrupling of the resistance will reduce the current to one-fourth its original value.)

f. I_new = 48 mA (Current is inversely proportional to resistance; a halving of the resistance will double the current.)

g. I_new = 24 mA (Current is directly proportional to voltage; a doubling of the voltage will double the current. But current is also inversely proportional to the resistance; a doubling of the resistance will halve the current. These two factors offset each other and there is no overall change in the current.)

h. I_new = 144 mA (Current is directly proportional to voltage; a tripling of the voltage will triple the current. But current is also inversely proportional to the resistance; a halving of the resistance will double the current. So the new current can be found by tripling and then doubling the old current of 24 mA.)

i. I_new = 6 mA (Current is directly proportional to voltage; a halving of the voltage will halve the current. But current is also inversely proportional to the resistance; a doubling of the resistance will halve the current. So the new current can be found by halving and then halving again the old current of 24 mA.)

7. Use the Ohm's law equation to provide numerical answers to the following questions:

a. An electrical device with a resistance of 3.0 Ω will allow a current of 4.0 amps to flow through it if a voltage drop of ________ Volts is impressed across the device.

b. When a voltage of 120 V is impressed across an electric heater, a current of 10.0 amps will flow through the heater if the resistance is ________ Ω.

c. A flashlight that is powered by 3 Volts and uses a bulb with a resistance of 60 Ω will have a current of ________ Amps.

See Answer

Use the equation V = I • R to solve for the unknown quantity.

a. An electrical device with a resistance of 3.0 Ω will allow a current of 4.0 amps to flow through it if a voltage drop of 12 Volts is impressed across the device.

b. When a voltage of 120 V is impressed across an electric heater, a current of 10.0 amps will flow through the heater if the resistance is 12 Ω.

c. A flashlight that is powered by 3 Volts and uses a bulb with a resistance of 60 Ω will have a current of 0.05 Amps.

8. Use the Ohm's law equation to determine the missing values in the following circuits.

See Answer

9. Refer to question 8 above. In the circuits of diagrams A and B, what method was used to control the current in the circuits? And in the circuits of diagrams C and D, what method was used to control the current in the circuits?

See Answer

In diagrams A and B, an alteration in the resistance was used to control the current. In going from diagram A to diagram B, the resistance was doubled from 3 Ω to 6 Ω; this caused the current to be reduced by a factor of 2.

In diagrams C and D, an alteration in the battery voltage was used to control the current. In going from diagram C to diagram D, the battery voltage was decreased by a factor of 2 (from 4 V to 2 V); this caused the current to be reduced by a factor of 2.