Multiplexing is defined as the sharing of a communications channel through local combining at a common point. In many cases, however, the communications channel must be efficiently shared among many users that are geographically distributed and that sporadically attempt to communicate at random points in time. Three schemes have been devised for efficient sharing of a single channel under these conditions; they are called frequency-division multiple access (FDMA), time-division multiple access (TDMA), and code-division multiple access (CDMA). These techniques can be used alone or together in telephone systems, and they are well illustrated by the most advanced mobile cellular systems.
In FDMA the goal is to divide the frequency spectrum into slots and then to separate the signals of different users by placing them in separate frequency slots. The difficulty is that the frequency spectrum is limited and that there are typically many more potential communicators than there are available frequency slots. In order to make efficient use of the communications channel, a system must be devised for managing the available slots. In the advanced mobile phone system (AMPS), the cellular system employed in the United States, different callers use separate frequency slots via FDMA. When one telephone call is completed, a network-managing computer at the cellular base station reassigns the released frequency slot to a new caller. A key goal of the AMPS system is to reuse frequency slots whenever possible in order to accommodate as many callers as possible. Locally within a cell, frequency slots can be reused when corresponding calls are terminated. In addition, frequency slots can be used simultaneously by multiple callers located in separate cells. The cells must be far enough apart geographically that the radio signals from one cell are sufficiently attenuated at the location of the other cell using the same frequency slot.
In TDMA the goal is to divide time into slots and separate the signals of different users by placing the signals in separate time slots. The difficulty is that requests to use a single communications channel occur randomly, so that on occasion the number of requests for time slots is greater than the number of available slots. In this case information must be buffered, or stored in memory, until time slots become available for transmitting the data. The buffering introduces delay into the system. In the IS54 cellular system, three digital signals are interleaved using TDMA and then transmitted in a 30-kilohertz frequency slot that would be occupied by one analog signal in AMPS. Buffering digital signals and interleaving them in time causes some extra delay, but the delay is so brief that it is not ordinarily noticed during a call. The IS54 system uses aspects of both TDMA and FDMA.
In CDMA, signals are sent at the same time in the same frequency band. Signals are either selected or rejected at the receiver by recognition of a user-specific signature waveform, which is constructed from an assigned spreading code. The IS95 cellular system employs the CDMA technique. In IS95 an analog speech signal that is to be sent to a cell site is first quantized and then organized into one of a number of digital frame structures. In one frame structure, a frame of 20 milliseconds’ duration consists of 192 bits. Of these 192 bits, 172 represent the speech signal itself, 12 form a cyclic redundancy check that can be used for error detection, and 8 form an encoder “tail” that allows the decoder to work properly. These bits are formed into an encoded data stream. After interleaving of the encoded data stream, bits are organized into groups of six. Each group of six bits indicates which of 64 possible waveforms to transmit. Each of the waveforms to be transmitted has a particular pattern of alternating polarities and occupies a certain portion of the radio-frequency spectrum. Before one of the waveforms is transmitted, however, it is multiplied by a code sequence of polarities that alternate at a rate of 1.2288 megahertz, spreading the bandwidth occupied by the signal and causing it to occupy (after filtering at the transmitter) about 1.23 megahertz of the radio-frequency spectrum. At the cell site one user can be selected from multiple users of the same 1.23-megahertz bandwidth by its assigned code sequence.
CDMA is sometimes referred to as spread-spectrum multiple access (SSMA), because the process of multiplying the signal by the code sequence causes the power of the transmitted signal to be spread over a larger bandwidth. Frequency management, a necessary feature of FDMA, is eliminated in CDMA. When another user wishes to use the communications channel, it is assigned a code and immediately transmits instead of being stored until a frequency slot opens.