In many telecommunications systems, it is necessary to represent an information-bearing signal with a waveform that can pass accurately through a transmission medium. This assigning of a suitable waveform is accomplished by modulation, which is the process by which some characteristic of a carrier wave is varied in accordance with an information signal, or modulating wave. The modulated signal is then transmitted over a channel, after which the original information-bearing signal is recovered through a process of demodulation.
Modulation is applied to information signals for a number of reasons, some of which are outlined below.
1. Many transmission channels are characterized by limited passbands—that is, they will pass only certain ranges of frequencies without seriously attenuating them (reducing their amplitude). Modulation methods must therefore be applied to the information signals in order to “frequency translate” the signals into the range of frequencies that are permitted by the channel. Examples of channels that exhibit passband characteristics include alternating-current-coupled coaxial cables, which pass signals only in the range of 60 kilohertz to several hundred megahertz, and fibre-optic cables, which pass light signals only within a given wavelength range without significant attenuation. In these instances frequency translation is used to “fit” the information signal to the communications channel.
2. In many instances a communications channel is shared by multiple users. In order to prevent mutual interference, each user’s information signal is modulated onto an assigned carrier of a specific frequency. When the frequency assignment and subsequent combining is done at a central point, the resulting combination is a frequency-division multiplexed signal, as is discussed in Multiplexing. Frequently there is no central combining point, and the communications channel itself acts as a distributed combine. An example of the latter situation is the broadcast radio bands (from 540 kilohertz to 600 megahertz), which permit simultaneous transmission of multiple AM radio, FM radio, and television signals without mutual interference as long as each signal is assigned to a different frequency band.
3. Even when the communications channel can support direct transmission of the information-bearing signal, there are often practical reasons why this is undesirable. A simple example is the transmission of a three-kilohertz (i.e., voiceband) signal via radio wave. In free space the wavelength of a three-kilohertz signal is 100 kilometres (60 miles). Since an effective radio antenna is typically as large as half the wavelength of the signal, a three-kilohertz radio wave might require an antenna up to 50 kilometres in length. In this case translation of the voice frequency to a higher frequency would allow the use of a much smaller antenna.
As is noted in analog-to-digital conversion, voice signals, as well as audio and video signals, are inherently analog in form. In most modern systems these signals are digitized prior to transmission, but in some systems the analog signals are still transmitted directly without converting them to digital form. There are two commonly used methods of modulating analog signals. One technique, called amplitude modulation, varies the amplitude of a fixed-frequency carrier wave in proportion to the information signal. The other technique, called frequency modulation, varies the frequency of a fixed-amplitude carrier wave in proportion to the information signal.
Digital modulation
In order to transmit computer data and other digitized information over a communications channel, an analog carrier wave can be modulated to reflect the binary nature of the digital baseband signal. The parameters of the carrier that can be modified are the amplitude, the frequency, and the phase.
Three methods of digital signal modulationA digital signal, representing the binary digits 0 and 1 by a series of on and off amplitudes, is impressed onto an analog carrier wave of constant amplitude and frequency. In amplitude-shift keying (ASK), the modulated wave represents the series of bits by shifting abruptly between high and low amplitude. In frequency-shift keying (FSK), the bit stream is represented by shifts between two frequencies. In phase-shift keying (PSK), amplitude and frequency remain constant; the bit stream is represented by shifts in the phase of the modulated signal.
If amplitude is the only parameter of the carrier wave to be altered by the information signal, the modulating method is called amplitude-shift keying (ASK). ASK can be considered a digital version of analog amplitude modulation. In its simplest form, a burst of radio frequency is transmitted only when a binary 1 appears and is stopped when a 0 appears. In another variation, the 0 and 1 are represented in the modulated signal by a shift between two preselected amplitudes.
If frequency is the parameter chosen to be a function of the information signal, the modulation method is called frequency-shift keying (FSK). In the simplest form of FSK signaling, digital data is transmitted using one of two frequencies, whereby one frequency is used to transmit a 1 and the other frequency to transmit a 0. Such a scheme was used in the Bell 103 voiceband modem, introduced in 1962, to transmit information at rates up to 300 bits per second over the public switched telephone network. In the Bell 103 modem, frequencies of 1,080 +/- 100 hertz and 1,750 +/- 100 hertz were used to send binary data in both directions.
When phase is the parameter altered by the information signal, the method is called phase-shift keying (PSK). In the simplest form of PSK a single radio frequency carrier is sent with a fixed phase to represent a 0 and with a 180° phase shift—that is, with the opposite polarity—to represent a 1. PSK was employed in the Bell 212 modem, which was introduced about 1980 to transmit information at rates up to 1,200 bits per second over the public switched telephone network.
In addition to the elementary forms of digital modulation described above, there exist more advanced methods that result from a superposition of multiple modulating signals. An example of the latter form of modulation is quadrature amplitude modulation (QAM). QAM signals actually transmit two amplitude-modulated signals in phase quadrature (i.e., 90° apart), so that four or more bits are represented by each shift of the combined signal. Communications systems that employ QAM include digital cellular systems in the United States and Japan as well as most voiceband modems transmitting above 2,400 bits per second.
A form of modulation that combines convolutional codes with QAM is known as trellis-coded modulation (TCM), which is described in Channel encoding. Trellis-coded modulation forms an essential part of most of the modern voiceband modems operating at data rates of 9,600 bits per second and above, including V.32 and V.34 modems.